很多场景都需要记录日志，在单片机这种存储资源有限的环境下，就需要一种轻量级的存储方法。
系统日志
在嵌入式设备应用场景中，系统日志时常可以监控设备软件的运行状态，及时记录问题点以及关键信息，方便开发人员后期定位以及解决问题。
本文将讲述一种简易的系统日志记录方法，用于保存设备的系统日志，视具体嵌入式设备情况而定，可存储在MCU内部Flash、外部Flash、EEPROM等，本文采用外部Flash作为示例展开介绍。
思路分析
对于系统日志可以当成文件系统，可以划分为三个重要部分：目录区、参数区、日志区。
- 目录区：根据日期进行归类，记录当天的日志的存储地址、日志索引、日志大小，通过目录可以获取整个日志文件的概况；
- 参数区：存储记录日志写位置、目录项个数、写状态等参数；
- 日志区：这是我们主要的存储区，记录系统的日志，支持环写。这三个区域都需要占用部分内存，可以自行分配大小。
实现的效果如下图所示，设置通过指令可查询到整个日志目录区的概况。
查询系统日志目录：AT+CATALOG?
LOG_ID:存储日志按日期分类，该ID用于查询对应日期日志,从1开始计数；
LOG_DATE:系统日志存储日期；
LOG_ADDR:系统日志存储外部FLASH地址；
LOG_OFFSET:系统日志存储偏移量（各日期日志大小，单位：字节）。
查询指定日期系统日志：AT+CATALOG=<LOG_ID>
LOG_ID:在查询系统日志目录时获取，当LOG_ID为0时，为查询整个系统日志。
另外提供移除系统日志（清除日志目录）指令：AT+RMLOG，后面将讲述具体实现。
FLASH内存划分
FLASH内存需要看具体设备进行合理划分，目录区、参数区与日志区实现环形存储，延长擦写寿命。
#define FLASH_SECTOR_SIZE ((uint32_t)0x001000)
#define FLASH_BLOCK_32K_SIZE ((uint32_t)0x008000)
#define FLASH_BLOCK_64K_SIZE ((uint32_t)0x010000)
#define SECTOR_MASK (FLASH_SECTOR_SIZE - 1) /*扇区掩码 ------*/
#define SECTOR_BASE(addr) (addr & (~SECTOR_MASK)) /*扇区的基地址 --*/
#define SECTOR_OFFSET(addr) (addr & SECTOR_MASK) /*扇区内的偏移 --*/
#define BLOCK_32K_BASE(addr) (addr & (~(FLASH_BLOCK_32K_SIZE)))
#define BLOCK_64K_BASE(addr) (addr & (~(FLASH_BLOCK_64K_SIZE)))
typedef enum {
FLASH_BLOCK_4K = 0, /**< flash erase block size 4k */
FLASH_BLOCK_32K = 1, /**< flash erase block size 32k */
FLASH_BLOCK_64K = 2 /**< flash erase block size 64k */
}flash_block_t;
/* flash 空间索引 */
typedef enum{
FLASH_CATALOG_ZONE = 0,
FLASH_SYSLOG_PARA_ZONE,
FLASH_SYSLOG_ZONE,
FLASH_ZONEX,
}flash_zone_e;
typedef struct{
flash_zone_e zone;
uint32_t start_address;
uint32_t end_address;
}flash_table_t;
/* 地址划分 */
static const flash_table_t flash_table[] = {
{ .zone = FLASH_CATALOG_ZONE, .start_address = 0x03200000, .end_address = 0x032FFFFF},
{ .zone = FLASH_SYSLOG_PARA_ZONE, .start_address = 0x03300000, .end_address = 0x033FFFFF},
{ .zone = FLASH_SYSLOG_ZONE, .start_address = 0x03400000, .end_address = 0x03FFFFFF},
};Flash底层实现擦除、读写操作接口，由读者自行实现。
flash_table_t *get_flash_table(flash_zone_e zone)
{
int i = 0;
for (i = 0; i < flash_zone_count; i++) {
if (zone == flash_table[i].zone)
return (flash_table_t *)&flash_table[i];
}
return NULL;
}
int flash_erase(flash_zone_e zone, uint32_t address, flash_block_t block_type)
{
flash_table_t *flash_table_tmp = get_flash_table(zone);
if (flash_table_tmp == NULL)
return -1;
if (address < flash_table_tmp->start_address ||address > flash_table_tmp->end_address)
return -1;
return bsp_spi_flash_erase(address, block_type);
}
int flash_write(flash_zone_e zone, uint32_t address, const uint8_t*data, uint32_t length)
{
flash_table_t *flash_table_tmp = get_flash_table(zone);
if (flash_table_tmp == NULL)
return -1;
if ((address < flash_table_tmp->start_address) ||((address + length) > flash_table_tmp->end_address))
return -1;
return bsp_spi_flash_buffer_write(address, (uint8_t *)data, length);
}
int flash_read(flash_zone_e zone, uint32_t address, uint8_t*buffer, uint32_t length)
{
flash_table_t *flash_table_tmp = get_flash_table(zone);
if (flash_table_tmp == NULL)
return -1;
if ((address < flash_table_tmp->start_address) ||((address + length) > flash_table_tmp->end_address))
return -1;
bsp_spi_flash_buffer_read(buffer, address, length);
return 0;
}参数与结构体定义
日志数据存储时间戳，便于问题定位，需要实现RTC接口调用。
typedef struct {
uint16_t Year; /* 年份:YYYY */
uint8_t Month; /* 月份:MM */
uint8_t Day; /* 日:DD */
uint8_t Hour; /* 小时:HH */
uint8_t Minute; /* 分钟:MM */
uint8_t Second; /* 秒:SS */
}time_t;
int bsp_rtc_get_time(time_t *date);参数区应当保证数据的正确性，应加入参数校验存储，定义校验结构体。
#define SYSTEM_LOG_MAGIC_PARAM 0x87654321 /* 日志参数标识符 */
typedef struct {
uint32_t magic; /* 参数标识符 */
uint16_t crc; /* 校验值 */
uint16_t len; /* 参数长度 */
} single_sav_t;参数区需记录当前日志记录的写位置，以及目录项个数，还有日志区和目录区环写状态，并且存储最新时间等等。
/* 日志区参数 */
typedef struct {
uint32_t write_pos; /* 写位置 */
uint32_t catalog_num; /* 目录项个数 */
uint8_t log_cyclic_status; /* 系统日志环形写状态 */
uint8_t catalog_cyclic_status; /* 日志目录环形写状态 */
time_t log_latest_time; /* 存储最新时间 */
}system_log_t;
/* 目录区参数 */
typedef struct {
uint32_t log_id; /* 日志索引 */
uint32_t log_addr; /* 日志地址 */
uint32_t log_offset; /* 日志偏移大小，单位：字节 */
time_t log_time; /* 日志存储时间 */
}system_catalog_t;
/* 系统日志参数 */
typedef struct {
single_sav_t crc_val;
system_log_t system_log;
system_catalog_t system_catalog;
}sys_log_param_t;
typedef struct {
uint8_t system_log_print_enable; /* 系统日志打印使能 */
uint16_t system_log_print_id; /* 打印指定id系统日志 */
uint32_t system_log_param_addr; /* 当前日志写地址 */
} sys_ram_t;
sys_ram_t SysRam;
sys_log_param_t SysLogParam;
sys_ram_t *gp_sys_ram = &SysRam;
sys_log_param_t *gp_sys_log = &SysLogParam;实现接口说明
CRC校验接口，可以自定义实现。
/* 16位CRC校验高位表 */
static const uint8_t auchCRCHi[]={
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40,0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,
0x00,0xc1,0x81,0x40,0x01,0xc0,0x80,0x41,0x01,0xc0,0x80,0x41,0x00,0xc1,0x81,0x40
};
/* 16位CRC校验低位表 */
static const uint8_t auchCRCLo[]={
0x00,0xc0,0xc1,0x01,0xc3,0x03,0x02,0xc2,0xc6,0x06,0x07,0xc7,0x05,0xc5,0xc4,0x04,
0xcc,0x0c,0x0d,0xcd,0x0f,0xcf,0xce,0x0e,0x0a,0xca,0xcb,0x0b,0xc9,0x09,0x08,0xc8,
0xd8,0x18,0x19,0xd9,0x1b,0xdb,0xda,0x1a,0x1e,0xde,0xdf,0x1f,0xdd,0x1d,0x1c,0xdc,
0x14,0xd4,0xd5,0x15,0xd7,0x17,0x16,0xd6,0xd2,0x12,0x13,0xd3,0x11,0xd1,0xd0,0x10,
0xf0,0x30,0x31,0xf1,0x33,0xf3,0xf2,0x32,0x36,0xf6,0xf7,0x37,0xf5,0x35,0x34,0xf4,
0x3c,0xfc,0xfd,0x3d,0xff,0x3f,0x3e,0xfe,0xfa,0x3a,0x3b,0xfb,0x39,0xf9,0xf8,0x38,
0x28,0xe8,0xe9,0x29,0xeb,0x2b,0x2a,0xea,0xee,0x2e,0x2f,0xef,0x2d,0xed,0xec,0x2c,
0xe4,0x24,0x25,0xe5,0x27,0xe7,0xe6,0x26,0x22,0xe2,0xe3,0x23,0xe1,0x21,0x20,0xe0,
0xa0,0x60,0x61,0xa1,0x63,0xa3,0xa2,0x62,0x66,0xa6,0xa7,0x67,0xa5,0x65,0x64,0xa4,
0x6c,0xac,0xad,0x6d,0xaf,0x6f,0x6e,0xae,0xaa,0x6a,0x6b,0xab,0x69,0xa9,0xa8,0x68,
0x78,0xb8,0xb9,0x79,0xbb,0x7b,0x7a,0xba,0xbe,0x7e,0x7f,0xbf,0x7d,0xbd,0xbc,0x7c,
0xb4,0x74,0x75,0xb5,0x77,0xb7,0xb6,0x76,0x72,0xb2,0xb3,0x73,0xb1,0x71,0x70,0xb0,
0x50,0x90,0x91,0x51,0x93,0x53,0x52,0x92,0x96,0x56,0x57,0x97,0x55,0x95,0x94,0x54,
0x9c,0x5c,0x5d,0x9d,0x5f,0x9f,0x9e,0x5e,0x5a,0x9a,0x9b,0x5b,0x99,0x59,0x58,0x98,
0x88,0x48,0x49,0x89,0x4b,0x8b,0x8a,0x4a,0x4e,0x8e,0x8f,0x4f,0x8d,0x4d,0x4c,0x8c,
0x44,0x84,0x85,0x45,0x87,0x47,0x46,0x86,0x82,0x42,0x43,0x83,0x41,0x81,0x80,0x40
};
/* 实现crc功能函数 */
static uint16_t CRC16(uint8_t* puchMsg, uint16_t usDataLen)
{
uint8_t uchCRCHi=0xff;
uint8_t uchCRCLo=0xff;
uint16_t uIndex;
while(usDataLen--) {
uIndex=uchCRCHi^*(puchMsg++);
uchCRCHi=uchCRCLo^auchCRCHi[uIndex];
uchCRCLo=auchCRCLo[uIndex];
}
return uchCRCHi<<8|uchCRCLo;
}保存系统日志参数，每实现写日志操作后都需要保存当前的参数值，防止意外丢失。
void save_system_log_param(void)
{
uint32_t i = 0;
uint32_t addr = 0;
uint32_t remainbyte = 0;
uint32_t start_addr;
int len = sizeof(sys_log_param_t);
uint8_t *pdata = (uint8_t *)&SysLogParam;
flash_table_t *flash_tmp = get_flash_table(FLASH_SYSLOG_PARA_ZONE);
/* 校验参数 */
gp_sys_log->crc_val.magic = SYSTEM_LOG_MAGIC_PARAM;
gp_sys_log->crc_val.len = sizeof(sys_log_param_t) - sizeof(single_sav_t);
gp_sys_log->crc_val.crc = CRC16(&pdata[sizeof(single_sav_t)], gp_sys_log->crc_val.len);
start_addr = gp_sys_ram->system_log_param_addr;
/* 剩余内存不够写，则重新从起始地址开始写，实现环形存储功能 */
if ((start_addr + len) > flash_tmp->end_address) {
start_addr = flash_tmp->start_address;
}
gp_sys_ram->system_log_param_addr = start_addr + len;
/* 首地址存储，擦除整个系统日志参数存储区，如果划分的内存较大，可能出现第一次擦写等待时间较长，
但实际应用嵌入式设备应该不会占用太多的内存存储系统日志，只当为辅助使用，有额外应用可自行实现 */
if (flash_tmp->start_address == start_addr) {
/*for (i = flash_tmp->start_address; i < flash_tmp->end_address; i+= FLASH_SECTOR_SIZE)
flash_erase(FLASH_SYSLOG_PARA_ZONE, SECTOR_BASE(i), FLASH_BLOCK_4K);
*/
addr = flash_tmp->start_address;
do {
if ((addr + FLASH_BLOCK_64K_SIZE) <= flash_tmp->end_address) {
flash_erase(FLASH_SYSLOG_PARA_ZONE, BLOCK_64K_BASE(i), FLASH_BLOCK_64K);
addr += FLASH_BLOCK_64K_SIZE;
} else if ((addr + FLASH_BLOCK_32K_SIZE) <= flash_tmp->end_address) {
flash_erase(FLASH_SYSLOG_PARA_ZONE, BLOCK_32K_BASE(i), FLASH_BLOCK_32K);
addr += FLASH_BLOCK_32K_SIZE;
} else if ((addr + FLASH_SECTOR_SIZE) <= flash_tmp->end_address) {
flash_erase(FLASH_SYSLOG_PARA_ZONE, SECTOR_BASE(i), FLASH_BLOCK_4K);
addr += FLASH_SECTOR_SIZE;
} else {
break;
}
} while (addr < flash_tmp->end_address);
}
remainbyte = FLASH_SECTOR_SIZE - (start_addr % FLASH_SECTOR_SIZE);
if (remainbyte > len) {
remainbyte = len;
}
while (1) {
flash_write(FLASH_SYSLOG_PARA_ZONE, start_addr, pdata, remainbyte);
if (remainbyte == len) {
break;
} else {
pdata += remainbyte;
start_addr += remainbyte;
len -= remainbyte;
remainbyte = (len > FLASH_SECTOR_SIZE) ? FLASH_SECTOR_SIZE : len;
}
}
}导入系统日志默认参数接口，初始化默认参数或者移除日志。
void load_system_log_default_param(void)
{
/* 系统日志默认参数 */
/* 目录环写状态标志 */
gp_sys_log->system_log.catalog_cyclic_status = 0x00;
/* 目录项个数 */
gp_sys_log->system_log.catalog_num = 0;
/* 日志环写标志 , 1:环写状态 */
gp_sys_log->system_log.log_cyclic_status = 0;
/* 设置默认值，实际会重新从RTC获取最新时间 */
gp_sys_log->system_log.log_latest_time.Year = 2019;
gp_sys_log->system_log.log_latest_time.Month = 5;
gp_sys_log->system_log.log_latest_time.Day = 8;
gp_sys_log->system_log.log_latest_time.Hour = 13;
gp_sys_log->system_log.log_latest_time.Minute = 14;
gp_sys_log->system_log.log_latest_time.Second = 10;
/* 日志写位置从0开始 */
gp_sys_log->system_log.write_pos = 0;
gp_sys_log->system_catalog.log_addr = 0;
gp_sys_log->system_catalog.log_id = 0;
gp_sys_log->system_catalog.log_offset = 0;
gp_sys_log->system_catalog.log_time.Year = 2019;
gp_sys_log->system_catalog.log_time.Month = 5;
gp_sys_log->system_catalog.log_time.Day = 8;
gp_sys_log->system_catalog.log_time.Hour = 12;
gp_sys_log->system_catalog.log_time.Minute = 12;
gp_sys_log->system_catalog.log_time.Second = 14;
gp_sys_log->crc_val.magic = SYSTEM_LOG_MAGIC_PARAM;
/* 导入默认参数后进行保存 */
save_system_log_param();
}设备开机或者复位都会进行导入系统日志参数操作，恢复日志读写参数，参数区为频繁读写操作区域，每一次写操作都会进行一次偏移，有效的导入参数方法是从参数区结束地址到起始地址进行扫描，扫描不到合法的参数则会导入默认日志参数。
/* 参数初始化，在终端启动时调用 */
int load_system_log_param(void)
{
uint32_t i = 0;
single_sav_t psav;
uint32_t end_addr;
uint32_t interal = sizeof(sys_log_param_t);
int data_len = sizeof(sys_log_param_t) - sizeof(single_sav_t);
uint8_t *pram = (uint8_t *)&SysLogParam;
flash_table_t *flash_tmp = get_flash_table(FLASH_SYSLOG_PARA_ZONE);
end_addr =flash_tmp->end_address - (flash_tmp->end_address - flash_tmp->start_address) % interal;
for (i = end_addr - interal; i > flash_tmp->start_address; i -= interal) {
flash_read(FLASH_SYSLOG_PARA_ZONE, i, (uint8_t *)&psav, sizeof(single_sav_t));
if ((psav.magic == SYSTEM_LOG_MAGIC_PARAM) && (psav.len ==data_len)) {
flash_read(FLASH_SYSLOG_PARA_ZONE, i + sizeof(single_sav_t), &pram[sizeof(single_sav_t)], data_len);
if (psav.crc != CRC16(&pram[sizeof(single_sav_t)], data_len))
continue;
gp_sys_ram->system_log_param_addr = i;
log_info("Load System Log Param Addr[0x%08x]!", gp_sys_ram->system_log_param_addr);
return 0;
}
}
/* 扫描不到合法的参数，导入默认系统日志参数 */
load_system_log_default_param();
/* 获取日志写地址 */
gp_sys_ram->system_log_param_addr = flash_tmp->start_address;
log_info("Load System Log Param Addr(Default)[0x%08x]!", gp_sys_ram->system_log_param_addr);
return 1;
}读写系统日志目录接口，读写指定日志索引目录信息。实际实现会定义最新的目录信息存储在日志参数区，当日期发生改变，则表示当前目录信息已经完结，将最新的目录信息录入日志目录区保存，最多每天写入一次目录区。
/* 读取日志目录区指定日志索引目录信息 */
int system_catalog_read(system_catalog_t *catalog, uint32_t id)
{
uint32_t addr;
int rlen = sizeof(system_catalog_t);
uint8_t *pbuf = (uint8_t *)catalog;
flash_table_t *flash_tmp = get_flash_table(FLASH_CATALOG_ZONE);
if (0 == id)
return -1;
addr = flash_tmp->start_address + (rlen * (id - 1));
if (addr > flash_tmp->end_address)
return -1;
return flash_read(FLASH_CATALOG_ZONE, addr, pbuf, rlen);
}
/* 写日志目录区目录信息 */
int system_catalog_write(system_catalog_t *catalog, uint32_t id)
{
uint32_t start_offset;
uint32_t start_addr;
uint32_t start_base;
uint32_t remainbyte;
int wlen = sizeof(system_catalog_t);
uint8_t *pdata = (uint8_t *)catalog;
flash_table_t *flash_tmp = get_flash_table(FLASH_CATALOG_ZONE);
if (0 == id) return -1;
start_addr = flash_tmp->start_address + wlen * (id - 1);
if ((start_addr + wlen) > flash_tmp->end_address) {
start_addr = flash_tmp->start_address;
}
/* 本扇区剩余空间大小 */
remainbyte = FLASH_SECTOR_SIZE - (start_addr % FLASH_SECTOR_SIZE);
/* 写入数据长度小于本扇区剩余长度，直接写入 */
if (remainbyte > wlen) {
remainbyte = wlen;
}
/* 写目录次数不会太频繁，视具体情况改写操作实现 */
while (1) {
start_base = SECTOR_BASE(start_addr);
start_offset = SECTOR_OFFSET(start_addr);
flash_read(FLASH_CATALOG_ZONE, start_base, sector_buf, FLASH_SECTOR_SIZE);
flash_erase(FLASH_CATALOG_ZONE, start_base, FLASH_BLOCK_4K);
memcpy((char *)§or_buf[start_offset], pdata, remainbyte);
flash_write(FLASH_CATALOG_ZONE, start_base, sector_buf, FLASH_SECTOR_SIZE);
if (remainbyte == wlen) {
break;
} else {
pdata += remainbyte;
start_addr += remainbyte;
wlen -= remainbyte;
remainbyte = (wlen > FLASH_SECTOR_SIZE) ? FLASH_SECTOR_SIZE : wlen;
}
}
return 0;
}打印系统日志目录区信息，可实现通过指令查询到目录区信息。
int system_catalog_all_print(void)
{
int i = 0;
system_catalog_t catalog;
printf("System Log Command Information:\r\n");
printf("Query Specifies Log : AT+CATALOG=<LOG_ID><CR><LF>\r\n");
printf("Query All Log : AT+CATALOG=<0><CR><LF>\r\n\r\n");
printf("Query All System Catalog:\r\n");
printf("LOG_ID LOG_DATE LOG_ADDR LOG_OFFSET \r\n");
for (i = 0; i < gp_sys_log->system_log.catalog_num; i++) {
/* 当前最新目录信息 */
if (i == (gp_sys_log->system_catalog.log_id - 1)) {
catalog = gp_sys_log->system_catalog; /* 获取当前最新目录信息 */
} else {
system_catalog_read(&catalog, i + 1);
}
printf("%d %04d-%02d-%02d 0x%08X %d \r\n",
catalog.log_id, catalog.log_time.Year, catalog.log_time.Month, catalog.log_time.Day,
catalog.log_addr, catalog.log_offset);
memset((char *)&catalog, 0, sizeof(system_catalog_t));
}
return 0;
}
读取指定日志目录索引信息接口，可指定日志索引或者读取全部日志数据。
int system_log_task(int argc)
{
int rlen = 0;
uint32_t offset, start_addr, end_addr;
system_catalog_t catalog;
flash_table_t *flash_tmp =get_flash_table(FLASH_SYSLOG_ZONE);
if (0 == gp_sys_ram->system_log_print_enable)
return 1;
gp_sys_ram->system_log_print_enable = 0x00;
if (gp_sys_ram->system_log_print_id == ALL_LOG_PRINT) {
/* log回环写标志,打印整个LOG存储区 */
if (0x01 == gp_sys_log->system_log.log_cyclic_status) {
start_addr = flash_tmp->start_address;
end_addr = flash_tmp->end_address;
offset = end_addr - start_addr;
} else {
start_addr = flash_tmp->start_address;
end_addr = start_addr + gp_sys_log->system_log.write_pos;
offset = gp_sys_log->system_log.write_pos;
}
} else { /* 读取指定ID日志 */
if (gp_sys_ram->system_log_print_id == gp_sys_log->system_catalog.log_id) {
catalog = gp_sys_log->system_catalog;
} else {
system_catalog_read(&catalog, gp_sys_ram->system_log_print_id);
}
start_addr = catalog.log_addr;
offset = catalog.log_offset;
}
if (0 == offset)
return 1;
while (1) {
rlen = (offset > 512) ? 512 : offset;
system_log_read(sector_buf, start_addr, rlen);
HAL_Delay(80);
/* 目录信息通过调式串口打印 */
bsp_debug_send(sector_buf, rlen);
start_addr += rlen;
offset -= rlen;
if (0 == offset)
break;
}
return 0;
}存储系统日志接口，实现更新存储日期，当写位置为扇区地址，则擦除一个扇区作为存储日志，这样避免每写一次就擦除一次。
int system_log_write(uint8_t *wbuf, int wlen)
{
uint32_t start_addr;
uint8_t *pdata = wbuf;
uint32_t remainbyte;
int system_catalog_max_id;
flash_table_t *flash_tmp =get_flash_table(FLASH_SYSLOG_ZONE);
/* 计算目录区的最大存储目录项个数 */
system_catalog_max_id = ((flash_tmp->end_address - flash_tmp->start_address) / sizeof(system_catalog_t));
start_addr = flash_tmp->start_address + gp_sys_log->system_log.write_pos;
/* 存储数据地址大于规划内存地址范围处理 */
if ((start_addr + wlen) > flash_tmp->end_address) {
start_addr = flash_tmp->start_address;
/* 写位置偏移量重置 */
gp_sys_log->system_log.write_pos = 0;
/* LOG回环存储标志置位 */
gp_sys_log->system_log.log_cyclic_status = 0x01;
}
/* 写位置偏移 */
gp_sys_log->system_log.write_pos += wlen;
if ((gp_sys_log->system_log.log_latest_time.Year != gp_sys_log->system_catalog.log_time.Year) ||
(gp_sys_log->system_log.log_latest_time.Month != gp_sys_log->system_catalog.log_time.Month) ||
(gp_sys_log->system_log.log_latest_time.Day != gp_sys_log->system_catalog.log_time.Day)) {
/* 日期改变，记录目录信息，当log_id为0，则不写入 */
system_catalog_write(&gp_sys_log->system_catalog, gp_sys_log->system_catalog.log_id);
/* 记录存储日期 */
gp_sys_log->system_catalog.log_time = gp_sys_log->system_log.log_latest_time;
if ((gp_sys_log->system_catalog.log_id + 1) >= system_catalog_max_id) {
gp_sys_log->system_log.catalog_num = system_catalog_max_id; /* 目录循环写，目录数应为最大 */
gp_sys_log->system_log.catalog_cyclic_status = 1; /* 目录回环写标志 */
} else {
if (0 == gp_sys_log->system_log.catalog_cyclic_status) {
/* 获取目录数 */
gp_sys_log->system_log.catalog_num = gp_sys_log->system_catalog.log_id + 1;
}
}
/* 存储最新目录项信息 */
gp_sys_log->system_catalog.log_id = (gp_sys_log->system_catalog.log_id + 1) % system_catalog_max_id;
gp_sys_log->system_catalog.log_addr = start_addr;
gp_sys_log->system_catalog.log_offset = wlen;
} else {
gp_sys_log->system_catalog.log_offset += wlen;
}
/* 写位置为存储起始地址并且不为扇区首地址 */
if ((flash_tmp->start_address == start_addr) && (SECTOR_OFFSET(flash_tmp->start_address))){
flash_read(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), sector_buf, FLASH_SECTOR_SIZE);
flash_erase(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), FLASH_BLOCK_4K);
/* 将扇区头部至起始地址区间的数据回写 */
flash_write(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), §or_buf[0], SECTOR_OFFSET(start_addr));
}
/* 写位置为扇区首地址，则擦除一个扇区的存储区 */
if (0 == SECTOR_OFFSET(start_addr)) {
flash_erase(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), FLASH_BLOCK_4K);
}
/* 本扇区剩余空间大小 */
remainbyte = FLASH_SECTOR_SIZE - (start_addr % FLASH_SECTOR_SIZE);
/* 写入数据长度小于本扇区剩余长度，直接写入 */
if (remainbyte > wlen) {
remainbyte = wlen;
}
while (1) {
flash_write(FLASH_SYSLOG_ZONE, start_addr, pdata, remainbyte);
if (remainbyte == wlen) {
break;
} else {
pdata += remainbyte;
start_addr += remainbyte;
wlen -= remainbyte;
remainbyte = (wlen > FLASH_SECTOR_SIZE) ? FLASH_SECTOR_SIZE : wlen;
/* 扇区首地址则擦除整个扇区，该扇区数据不保存 */
if (0 == SECTOR_OFFSET(start_addr)) {
flash_erase(FLASH_SYSLOG_ZONE, SECTOR_BASE(start_addr), FLASH_BLOCK_4K);
}
}
}
/* 环形存储参数 */
save_system_log_param();
return 0;
}系统调试对接
为了更好记录系统日志，将应用调试等级结合一块，实现记录错误调试信息以及需要保存的关键信息。定义的调试等级有：关闭调试等级、错误调试等级、警告调试等级、关键调试等级、debug调试等级，而LOG_RECORD_LEVEL将主动保存日志并输出信息，LOG_ERROR_LEVEL会存储对应的日志信息，但需要根据应用调试等级输出信息。设置与读取应用调试等级由读者自行定义。
#define LOG_CLOSE_LEVEL 0x00 /* 关闭调试信息 */
#define LOG_ERROR_LEVEL 0x01 /* 错误调试信息 */
#define LOG_WARN_LEVEL 0x02 /* 警告调试信息 */
#define LOG_INFO_LEVEL 0x03 /* 关键调试信息 */
#define LOG_DEBUG_LEVEL 0x04 /* debug调试信息 */
#define LOG_RECORD_LEVEL 0x10 /* 保存日志并输出信息 */
#define LOG_PRINT_LEVEL 0xff
#define SET_LOG_LEVEL(LEVEL) (gp_sys_param->system_print_level = LEVEL)
#define GET_LOG_LEVEL() (gp_sys_param->system_print_level)
#define log_debug(fmt, args...) log_format(LOG_DEBUG_LEVEL, fmt, ##args)
#define log_info(fmt, args...) log_format(LOG_INFO_LEVEL, fmt, ##args)
#define log_warn(fmt, args...) log_format(LOG_WARN_LEVEL, fmt, ##args)
#define log_error(fmt, args...) log_format(LOG_ERROR_LEVEL, fmt, ##args)
#define log_record(fmt, args...) log_format(LOG_RECORD_LEVEL, fmt, ##args)
#define printf(fmt, args...) log_format(LOG_PRINT_LEVEL, fmt, ##args)
typedef struct {
int level;
char *fmt_str;
}system_print_fmt_t;
system_print_fmt_t system_print_fmt_list[] = {
{ .level = LOG_ERROR_LEVEL, .fmt_str = "<error>:"},
{ .level = LOG_WARN_LEVEL, .fmt_str = "<warn>:"},
{ .level = LOG_INFO_LEVEL, .fmt_str = "<info>:"},
{ .level = LOG_DEBUG_LEVEL, .fmt_str = "<debug>:"},
{ .level = LOG_RECORD_LEVEL, .fmt_str = "<record>:"},
};
int log_format(uint8_t level, const char *fmt, ...)
{
#define TIME_PREFIX_SIZE (21)
#define PRINT_MAX_SIZE (1024 + TIME_PREFIX_SIZE)
va_list args;
int num = 0, i = 0, fmt_index = 0;
int fmt_str_len = 0, ret = -1;
int file_str_len = 0, line_str_len = 0;
char line_buf[20] = {0};
static char buf[PRINT_MAX_SIZE];
static QueueHandle_t sem = NULL;
time_t time = {0};
/* 针对os系统 */
if (NULL == sem) {
sem = xSemaphoreCreateCounting(1, 1); /* always think of success */
}
xSemaphoreTake(sem, portMAX_DELAY);
ret = -1;
fmt_str_len = 0;
if (level != LOG_PRINT_LEVEL) {
if ((GET_LOG_LEVEL() < level) && (level != LOG_RECORD_LEVEL) && (level != LOG_ERROR_LEVEL))
goto exit_end;
for (i = 0; i < SYSTEM_PRINT_FMT_LIST_MAX; i++) {
if (level == system_print_fmt_list[i].level) {
fmt_index = i;
break;
}
}
if (i > SYSTEM_PRINT_FMT_LIST_MAX) {
goto exit_end;
}
fmt_str_len = strlen(system_print_fmt_list[fmt_index].fmt_str);
strncpy((char *)&buf[TIME_PREFIX_SIZE], system_print_fmt_list[fmt_index].fmt_str, fmt_str_len);
}
va_start(args, fmt);
num = vsnprintf((char *)&buf[fmt_str_len + TIME_PREFIX_SIZE], PRINT_MAX_SIZE - fmt_str_len - TIME_PREFIX_SIZE - 2, fmt, args);
va_end(args);
if (num <= 0) {
goto exit_end;
}
if (level != LOG_PRINT_LEVEL) {
num += fmt_str_len;
buf[num + TIME_PREFIX_SIZE] = '\r';
buf[num + TIME_PREFIX_SIZE + 1] = '\n';
num += 2;
}
if ((GET_LOG_LEVEL() < level) && (level == LOG_ERROR_LEVEL)) {
//do nothing
} else {
ret = bsp_debug_send((uint8_t*)&buf[TIME_PREFIX_SIZE], num);
}
if ((LOG_ERROR_LEVEL == level) || (LOG_RECORD_LEVEL == level)) {
bsp_rtc_get_time(&time);
sprintf(&buf[0], "[%04d-%02d-%02d %02d:%02d:%02d",
time.Year, time.Month, time.Day,time.Hour, time.Minute, time.Second);
buf[TIME_PREFIX_SIZE - 1] = ']';
gp_sys_log->system_log.log_latest_time = time;
system_log_write((uint8_t *)buf, num + TIME_PREFIX_SIZE);
}
exit_end:
xSemaphoreGive(sem);
return ret;
}结语
本文提供的一种简易嵌入式设备系统日志记录方法，代码量不多，实现简单，针对不同的设备需要合理规划内存使用。
根据软件运行状态，合适加入调试信息并保存对应的日志信息，方便开发人员了解系统或软件运行状况，协助开发分析数据资源从而更好完善系统，提高定位以及解决问题的效果。
来源地址：
声明：本文素材来源网络，版权归原作者所有。如涉及作品版权问题，请与我联系删除。
END
作者：strongerHuang
来源：strongerHuang
推荐阅读
欢迎大家点赞留言，更多Arm技术文章动态请关注极术社区嵌入式客栈专栏欢迎添加极术小姐姐微信（id:aijishu20)加入技术交流群，请备注研究方向。
